[omaroz]

السلام عليكم
اخواني لدي كود مكتوب بلغة السي باستخدام برنامج الMPLAP اريد تحويل الكود الى صيغة برنامج المايكرو سي لانه يحتوي على مكتبة شاشة نوكيا 1100 ومش عارف احول الكود ارجوكم ساعدوني هذا هو الكود

//////////////////////
/// lcd1100.c
///
/// Badr Ghatasheh (demonspells)
/// 11/3/2011
//////////////////////
#define sclk PIN_B4
#define sda PIN_B5
#define cs PIN_B6
#define rst PIN_B7

#define CMD 0
#define DATA 1



void Lcd_Init(void);
void Lcd_Write(int1 cd,unsigned char c);
void Lcd_Clear(void);
void SetX(char x);
void SetY(char y);
void Gotoxy(char x,char y);
void VLine(char x,char y,char on);
void Line(unsigned char x,unsigned char y,unsigned char y2,unsigned char on);
void print_char(char c);
char bitaddr;


// lookup table, here you can modify the font
byte const FontLookup1[48][5]={
{0x00, 0x00, 0x00, 0x00, 0x00},// (space)
{0x00, 0x00, 0x5F, 0x00, 0x00},// !
{0x00, 0x07, 0x00, 0x07, 0x00},// "
{0x14, 0x7F, 0x14, 0x7F, 0x14},// #
{0x24, 0x2A, 0x7F, 0x2A, 0x12},// $
{0x23, 0x13, 0x08, 0x64, 0x62},// %
{0x36, 0x49, 0x55, 0x22, 0x50},// &
{0x00, 0x05, 0x03, 0x00, 0x00},// '
{0x00, 0x1C, 0x22, 0x41, 0x00},// (
{0x00, 0x41, 0x22, 0x1C, 0x00},// )
{0x08, 0x2A, 0x1C, 0x2A, 0x08},// *
{0x08, 0x08, 0x3E, 0x08, 0x08},// +
{0x00, 0x50, 0x30, 0x00, 0x00},// ,
{0x08, 0x08, 0x08, 0x08, 0x08},// -
{0x00, 0x30, 0x30, 0x00, 0x00},// .
{0x20, 0x10, 0x08, 0x04, 0x02},// /
{0x3E, 0x51, 0x49, 0x45, 0x3E},// 0
{0x00, 0x42, 0x7F, 0x40, 0x00},// 1
{0x42, 0x61, 0x51, 0x49, 0x46},// 2
{0x21, 0x41, 0x45, 0x4B, 0x31},// 3
{0x18, 0x14, 0x12, 0x7F, 0x10},// 4
{0x27, 0x45, 0x45, 0x45, 0x39},// 5
{0x3C, 0x4A, 0x49, 0x49, 0x30},// 6
{0x01, 0x71, 0x09, 0x05, 0x03},// 7
{0x36, 0x49, 0x49, 0x49, 0x36},// 8
{0x06, 0x49, 0x49, 0x29, 0x1E},// 9
{0x00, 0x36, 0x36, 0x00, 0x00},// :
{0x00, 0x56, 0x36, 0x00, 0x00},// ;
{0x00, 0x08, 0x14, 0x22, 0x41},// <
{0x14, 0x14, 0x14, 0x14, 0x14},// =
{0x41, 0x22, 0x14, 0x08, 0x00},// >
{0x02, 0x01, 0x51, 0x09, 0x06},// ?
{0x32, 0x49, 0x79, 0x41, 0x3E},// *
{0x7E, 0x11, 0x11, 0x11, 0x7E},// A
{0x7F, 0x49, 0x49, 0x49, 0x36},// B
{0x3E, 0x41, 0x41, 0x41, 0x22},// C
{0x7F, 0x41, 0x41, 0x22, 0x1C},// D
{0x7F, 0x49, 0x49, 0x49, 0x41},// E
{0x7F, 0x09, 0x09, 0x01, 0x01},// F
{0x3E, 0x41, 0x41, 0x51, 0x32},// G
{0x7F, 0x08, 0x08, 0x08, 0x7F},// H
{0x00, 0x41, 0x7F, 0x41, 0x00},// I
{0x20, 0x40, 0x41, 0x3F, 0x01},// J
{0x7F, 0x08, 0x14, 0x22, 0x41},// K
{0x7F, 0x40, 0x40, 0x40, 0x40},// L
{0x7F, 0x02, 0x04, 0x02, 0x7F},// M
{0x7F, 0x04, 0x08, 0x10, 0x7F},// N
{0x3E, 0x41, 0x41, 0x41, 0x3E}};// O

byte const FontLookup2[48][5]={
{0x7F, 0x09, 0x09, 0x09, 0x06},// P
{0x3E, 0x41, 0x51, 0x21, 0x5E},// Q
{0x7F, 0x09, 0x19, 0x29, 0x46},// R
{0x46, 0x49, 0x49, 0x49, 0x31},// S
{0x01, 0x01, 0x7F, 0x01, 0x01},// T
{0x3F, 0x40, 0x40, 0x40, 0x3F},// U
{0x1F, 0x20, 0x40, 0x20, 0x1F},// V
{0x7F, 0x20, 0x18, 0x20, 0x7F},// W
{0x63, 0x14, 0x08, 0x14, 0x63},// X
{0x03, 0x04, 0x78, 0x04, 0x03},// Y
{0x61, 0x51, 0x49, 0x45, 0x43},// Z
{0x00, 0x00, 0x7F, 0x41, 0x41},// [
{0x02, 0x04, 0x08, 0x10, 0x20},// "\"
{0x41, 0x41, 0x7F, 0x00, 0x00},// ]
{0x04, 0x02, 0x01, 0x02, 0x04},// ^
{0x40, 0x40, 0x40, 0x40, 0x40},// _
{0x00, 0x01, 0x02, 0x04, 0x00},// `
{0x20, 0x54, 0x54, 0x54, 0x78},// a
{0x7F, 0x48, 0x44, 0x44, 0x38},// b
{0x38, 0x44, 0x44, 0x44, 0x20},// c
{0x38, 0x44, 0x44, 0x48, 0x7F},// d
{0x38, 0x54, 0x54, 0x54, 0x18},// e
{0x08, 0x7E, 0x09, 0x01, 0x02},// f
{0x08, 0x14, 0x54, 0x54, 0x3C},// g
{0x7F, 0x08, 0x04, 0x04, 0x78},// h
{0x00, 0x44, 0x7D, 0x40, 0x00},// i
{0x20, 0x40, 0x44, 0x3D, 0x00},// j
{0x00, 0x7F, 0x10, 0x28, 0x44},// k
{0x00, 0x41, 0x7F, 0x40, 0x00},// l
{0x7C, 0x04, 0x18, 0x04, 0x78},// m
{0x7C, 0x08, 0x04, 0x04, 0x78},// n
{0x38, 0x44, 0x44, 0x44, 0x38},// o
{0x7C, 0x14, 0x14, 0x14, 0x08},// p
{0x08, 0x14, 0x14, 0x18, 0x7C},// q
{0x7C, 0x08, 0x04, 0x04, 0x08},// r
{0x48, 0x54, 0x54, 0x54, 0x20},// s
{0x04, 0x3F, 0x44, 0x40, 0x20},// t
{0x3C, 0x40, 0x40, 0x20, 0x7C},// u
{0x1C, 0x20, 0x40, 0x20, 0x1C},// v
{0x3C, 0x40, 0x30, 0x40, 0x3C},// w
{0x44, 0x28, 0x10, 0x28, 0x44},// x
{0x0C, 0x50, 0x50, 0x50, 0x3C},// y
{0x44, 0x64, 0x54, 0x4C, 0x44},// z
{0x00, 0x08, 0x36, 0x41, 0x00},// {
{0x00, 0x00, 0x7F, 0x00, 0x00},// |
{0x00, 0x41, 0x36, 0x08, 0x00},// }
{0x08, 0x08, 0x2A, 0x1C, 0x08},// ->
{0x08, 0x1C, 0x2A, 0x08, 0x08} // <-
};


// clear LCD
void Lcd_Clear(void){
unsigned int i;
Lcd_Write(CMD,0x40); // Y = 0
Lcd_Write(CMD,0xb0);
Lcd_Write(CMD,0x10); // X = 0
Lcd_Write(CMD,0x0);
Lcd_Write(CMD,0xae); // disable display;
for(i=0;i<255;i++)
Lcd_Write(DATA,0x00);
for(i=0;i<255;i++)
Lcd_Write(DATA,0x00);
for(i=0;i<255;i++)
Lcd_Write(DATA,0x00);
for(i=0;i<99;i++)
Lcd_Write(DATA,0x00);
Lcd_Write(CMD,0xaf); // enable display;
}

// init LCD
void Lcd_Init(void){
output_low(cs);
output_low(rst);
delay_ms(5); // 5mS so says the stop watch(less than 5ms will not work)
output_high(rst);
Lcd_Write(CMD,0x20); // write VOP register
Lcd_Write(CMD,0x90);
Lcd_Write(CMD,0xA4); // all on/normal display
Lcd_Write(CMD,0x2F); // Power control set(charge pump on/off)
Lcd_Write(CMD,0x40); // set start row address = 0
Lcd_Write(CMD,0xb0); // set Y-address = 0
Lcd_Write(CMD,0x10); // set X-address, upper 3 bits
Lcd_Write(CMD,0x0); // set X-address, lower 4 bits
Lcd_Write(CMD,0xC8); // mirror Y axis (about X axis)
Lcd_Write(CMD,0xa1); // Invert screen in horizontal axis
Lcd_Write(CMD,0xac); // set initial row (R0) of the display
Lcd_Write(CMD,0x07);
//Lcd_Write(CMD,0xF9); //
Lcd_Write(CMD,0xaf); // display ON/OFF

Lcd_Clear(); // clear LCD
Lcd_Write(CMD,0xa7); // invert display
delay_ms(100);
Lcd_Write(CMD,0xa6); // normal display (non inverted)
delay_ms(100);
}


void Lcd_Write(int1 cd,unsigned char c){
int i;
output_low(cs);
output_low(sclk);
output_bit(sda,cd);
output_high(sclk);

for(i=0;i<8;i++){
output_low(sclk);
if((c & 0x80))
output_high(sda);
else
output_low(sda);
output_high(sclk);
c <<= 1;
delay_us(10);
}
output_high(cs);
}


void SetX(char x){
Lcd_Write(CMD,0x10 | ((x>>4)&0x7));
Lcd_Write(CMD,x & 0x0f);
}

void SetY(char y){
char aux = 0;
while(y>7){
y -=8;
aux ++;
}

bitaddr = y-1;
Lcd_Write(CMD,0xB0 | (aux & 0x0f));
}

void Gotoxy(char x,char y){
Lcd_Write(CMD,(0xB0|(y&0x0F))); // Y axis initialisation: 0100 yyyy
Lcd_Write(CMD,(0x00|(x&0x0F))); // X axis initialisation: 0000 xxxx ( x3 x2 x1 x0)
Lcd_Write(CMD,(0x10|((x>>4)&0x07))); // X axis initialisation: 0010 0xxx ( x6 x5 x4)

}


//x dir > y dir from last line to ^
void VLine(char x,char y,char on){
char aux[8];
char i;

for(i=0;i<8;i++)
aux[i] = 0;

i = 7;
while(y > 9){
aux[i] = 0xff;
y -= 8;
i--;
}

while(y > 0){
aux[i] >>= 1;
aux[i] |= 0x80;
y --;
}



for(y=0;y<8;y++){
Lcd_Write(CMD,0xB0 | y);
SetX(x);
Lcd_Write(DATA,aux[y]);
}

}

// xdir is > y is always < than y2 can be used for graphs
void Line(unsigned char x,unsigned char y,unsigned char y2,unsigned char on){
char aux[8];
char i,o;
char c=1;
char index;



for(i=0;i<8;i++)
aux[i] = 0;


index = 0;
for(i=0;i<64;i++){

if(i >= y && i <= y2){
aux[index] |= c << o;
}

o ++;
if(o == 8){
o = 0;
index ++;
}
}


for(i=0;i<8;i++){
Lcd_Write(CMD,0xB0 | i);
SetX(x);
Lcd_Write(DATA,aux[i]);
}


}



void print_char(char c){
int i;


for ( i = 0; i < 5; i++ ){
if(c<0x50) Lcd_Write(DATA,FontLookup1[c - 0x20][i] << 1);
else if(c>0x4f) Lcd_Write(DATA,FontLookup2[c - 0x50][i] << 1);
}
Lcd_Write(DATA,0x00);
Lcd_Write(CMD,0xaf);
}






#include <16f877a.h>
#fuses HS,NOWDT,NOLVP,NOPROTECT
#use delay(clock=4000000)
#use rs232(baud=19200, xmit=PIN_C6, rcv=PIN_C7,stream=com0)

#include "lcd1100.c"

void main (void) {

Lcd_Init();
Gotoxy(5,0);
printf(print_char,"Nokia 1100 LCD");
Gotoxy(40,4);
printf(print_char,"");

while(1);
}