 |
|
|
|
||||||
يونيفرسال لاين( صيني)
السلام عليكم يونيفرسال لاين صيني لجميع الاحجام كما هو موضح بالصور. ومرفق كتيب الشرح والاستعمال باللغة الانكليزية. وهذا اللاين الصيني وصل لسوريا ولا اعلم اذا كان موجود بدول اخرى. http://www.qariya.com/vb/showthread....031#post621031 ملخص كتيب التعليمات المرفق في الشكل الاول يبين بيانات اطراف اللاين بالنسبة للc1 و c2 عندما يكون جهد ال +B 110 فولت و 115 فولت توصله لل C1 وعندما يكون الجهد ما بين 130 و135 فولت توضله لل C2 في الشكل التاني اللاين راكب على فيبره وله دائرتان الدائره الاولى مسامير الللاين موصله بها والدائرة الثانيه المحاذيه لها مساميرها ظاهرة اكثر ويمكنك اجراء التوصيلات ( التعديلات حسب المطلوب) على الفيبرة بواسطة اسلاك وذلك لسهولة التركيب وعدم اجراء هذه التعديلات على الشسيه. تحذير: عند تركيب اللاين الجديد انزع بورد سوكة الشاشه افحص جهد الفيلمنت وجهد الفيديو وباقي الجهودات اذا كانت طبيعية وذلك حتى لا يحصل اي خطأ يؤدي الى فقدان الشاشه ومشاكل اخرى. في الشكل الثالث يبين جهودات اللاين وفي حال عدم وجود على شسيه اللاين بعمل كل طرف فمن السهل ان تحدد جهد + B وحهد الكولكتر والارضي وجهد ال 180 فولت ( عبر مكثف كيماوي 250 فولت) والفيلمنت وهما موصلان دائما عبر اسلاك الى كعب الشاشه اما جهد ال ABL دائما موصله عبر مكثف 0.047-10UF . وباقي الجهودات _14 و+14 و 25 فولت من السهل ايضا معرفتها حسب توصيلها بالشسيه. اما ال PULSE PIN عادة تكون موصله وعبر مقاومة الى نقطة AFC في متكاملة العمليات. وفي حال عدم وجود اي جهد يمكنك عمل لفات حول فحمة اللاين واستخراجه لكن بحذر وعدم التوصيل الا بعد التأكد من الجهد المطلوب. في حال وجود 2 فوكس باللاين القديم وخاصة لتلفزيونات الفلات . يتم توصيل نقطي الفوكس مع بعض في الجهاز وتوصيلهم بفوكس اللاين اليونيفرسال. اذا ظهرت بعض التغييرات من صورة صغيرة او كبيرة بعد تركيب لاين اليونيفرسال الحل. في حال الصورة كبيرة غير سعة مكثف ال CORRECTION SIZE اي مكثف نهاية الدفلكشن بقيمه اكبر او نقص سعة مكثف بور اللاين والقيمة المسموح بها هي 20 بالمئة والاسوف تؤدي الى ضرب ترنزستور اللاين وسبركة الشاشه. وعندما تكون الصورة صغيرة صغر قيمة مكثف نهاية الدفلكشن او كبر قيمة مكثف بور اللاين وطبعا القيمة المسموح بها ايضا 20 بالمئة فقط.. يرجى مراجعة هذا الموضوع. قيم مكثف بور اللاين اتمنى ان اكون وفقت في تلخيص الكتيب واي استفسار انا تحت امركم.     ¢ñ¡¢General Theories
Huamei"All Purpose Color TV Line Output Transformer" is actually a line output transformer with high voltage output and complete genres.Refer to Figure 1 for internal principles. From Figure 1 we can see that Color TV line output voltage is comparatively high in compliance with requirement of most color TVs.Therefore,as long as there is appropriate connection pin,it is reliable to replace Color TV's line of original machine. ¢ò¡¢Connection Method Figure 2 is a description drawing of this Color TV line,with two circle of pins inside and outside,in which pins at internal circle are shorter,these are leding feet of internal functions;pins at outer circle are longer,these are all empty pins.During application.make different connections among pins of internal circle and outer circle,pins at outer circle have pin functions of line output transformer for color TVs,then weld outer circle pins of this Color TV line to original machine,so as to realize replacement of original Color TV line. Caution  rior to installation of all-purpose Color TV line,please make sure to unplug Video amplifiler board of original machine.After installation of all-purpose Color TV line,please test filament voltage,video amplifier voltage and voltage of acceleration node to be normal,and install TV amplifer's board later,or it can easily damage the kinescope. ¢ó¡¢Application Examples When applying all-purpose color TV line output transformer,it is imperative to verify function of each pin,pin sequence marking for line output transformer of each color TV vendors,clockwise or counter-clockwise.Therefore,when verifying function of each pin for color TVs,only by looking at drawing of the original machine is not enough.It is necessary to associate actual PCBs to determine the function of each pin. Next is an explanation of Konka P3486C color TV for instructions: Figure 3 is a pin function figure for line output transformer of Konica P3486C color TVs After determining function of each pin from output transformer of the original machine,it is viable to connect corresponding internal and external pins of all-purpose Color TV line.Ways are using sections of short lead wire to connect corresponding pins of all purpose Color TV line,see Figure 4,making functions of each pin at outer circle corresondent to function of each pin of Color TV line in original machine.(Note in quantily of outer circle for all purpose Color TV line might be different from the pin quantily of Color TV line of original machine.During connection,it is imperative to select the one closest to pin positions of original machine,so as to install all purpose Color TV line on PCB.)After connection of each pin and confirmation of correction,it is viable to insert modified external pins.of all purpose Color TV line to welding hole of each pin from original Color TV line for good welding.(Useless external circle pins can be cut off ).Therefore,connect high and medium voltage,startup for adjustment,and speed up and foucs on the electic voltage. ¢ô¡¢Troubleshooting 1¡¢How to make judgment on functions of each pin for Color TV line of original machine without drawing? when there are no drawings,it is easy to judge power supply pin,line output transistor C machine and grounding pin of Color TV line in original machine.Video amplifier and filament pin are mostly connected to rear board through lead wire,and video amplifier is connected to the rear board after rectifying and wave-filtering,wave-filtering capacitor has a withstand voltage of 250V£¬therefore£¬it is easier to find video ampplifiler voltage pin and filament pin.Characteristics of ABL pin is a certain pin of Color TV line's connected to the ground with a 0.047-10uf capacitor,and connect to light PCB with an ABL pin through an electric resistence.+15V,-15V,25V and 45V are mostly power supply for output circuit,when using-14V or -16V of original machine,it is viable to use -15V pin of this Color TV line.Under mormal conditions,postitive and negative 15V are used together for a field output circuit,25V power supplying is a certain field output circuit,so it is effective to make judgment of line change pin voltage which is connected to field output circuit.Pulse pin is normally wired through resistance capacitance and delivered to AFC pin of line scanning module and line pulse input pin of decoding module.Therefore,it is viable to find the pin by analyzing generous functions of each section of clectric circuit of original machine.Of course,if there is a book of replacement material for line output transformer,it would be easier to make judgment on pin functions. 2¡¢What can we do if there is no individual coil from Color TV line of original machine? Multiple voltage output of all purpose Color TV line is capable of supplying requirements from most color TVs.But individual voltage for a minority of color TVs is not available for all purpose Color TV line.By then,it is viable to use enameled wire or fine flexible cord to circle on magnetic cord of all purpose Color TV line to acquire necessary voltage.But it is worth noted that when adding up the coil,it is imperative to start,from fewer circles to more circles,and add circles while testing the machine.It is forbidden to connect electric circuit for machine testing after adding up too many circles,or original machine can be damaged by high voltage produced by added coil. To replace double-focus color lines of flat color TV sers,connect the two focusing electrodes of the original television and attach them together to the focusing line of the universal color line. 3¡¢After installation of all purpose Color TV line,what will happen if there is too large or small of row width? ¡¡¡¡After installing all purpose Color TV line,when row width is too large or small,it is¡¡imperative to make adjustments to row width potentiometer,or enter maintence staus to adjust row width data (IC2 control digital loader).it is viable to use larger size correction capacitor or reduce retrace interval capacitor to address the problem.However,maximal changing volume of retrace interval capacitor can not exceed 20% of original capacity,or it is easy to damage line output transistors.When row width is too small,it is viable to use small size correction capacitor or enlarged retrace interval capacitor to solve the problem. التعديل الأخير تم بواسطة : احمد حمادي بتاريخ 01-04-2012 الساعة 09:52 PM |
| اعلانات |
|
||||||
|
|
| اعلانات اضافية ( قم بتسجيل الدخول لاخفائها ) | |
|
|
|
||||||
|
|
|
||||||
|
|
|
||||||
|
|
|
||||||
|
|
|
||||||
|
|
|
||||||
|
|
